630184_4 IB Installation Manual NZ IB1100, IB850, IB600 (Log Fire / Coal Fire) Installation Manual NEW ZEALAND EDITION Importa
630184_4 IB Installation Manual NZ 10 10.0 Power Supply: Whilst the cavity is being created consideration should be given to appropriate location o
630184_4 IB Installation Manual NZ 11 11.0 Installing the Flue System: Non-Masonry Timber Frame Cavity: The heater must be flued to the outside via
630184_4 IB Installation Manual NZ 12 12.0 Flue Assembly Secure the Flue spacer bracket (G3003)
630184_4 IB Installation Manual NZ 13 12.1 Installing the Flue Terminal Cut the flue termination to the height specified on the attached “Flue po
630184_4 IB Installation Manual NZ 14 12.2 The top of the flue must be capped with an appropriate anti down draft cowl. Note: As per national standa
630184_4 IB Installation Manual NZ 15 FROM AS/NZS 5601, please ensure compliance to all other relevant sections of this code. 2.6.13 FLUE TERMINALS
630184_4 IB Installation Manual NZ 16 FLAT ROOFS WITH NO PARAPET STRUCTURE CLOSE TO FLUE TERMINALFLUE CLOSE TO PARAPET MULTIPLE STRUCTURES (Envelope
630184_4 IB Installation Manual NZ 17 12.4 Fixing the Flue to the Cavity A length of Angle should be attached to the inside of the timber frame ca
630184_4 IB Installation Manual NZ 18 13.0 Masonry Cavity and Chimney: The heater can be flued with 100mm flexible aluminum ducting in accordance w
630184_4 IB Installation Manual NZ 19 14.3 It is recommended that a gas isolating valve be installed as close to the regulator on the
630184_4 IB Installation Manual NZ 2 Note: THERE ARE A FEW THINGS TO CONSIDER BEFORE INSTALLATION Cavity Dimensions, Clearances and fitting the
630184_4 IB Installation Manual NZ 20 15.3 Attach the Top-Rear: Attach the top-rear panel to the Sides and Rear panels, with the flanges of the To
630184_4 IB Installation Manual NZ 21 17.0 Gas Fireplace Installation: Attached to the base of the Zero Clearance Kit are guide rails. The inside e
630184_4 IB Installation Manual NZ 22 18.0 Attaching the Flue to the Fireplace: Once the gas fireplace has been inserted into the ZCK
630184_4 IB Installation Manual NZ 23 20.0 Fixing the Heater to the Base and Wall: There are several ways that the heater can be fi
630184_4 IB Installation Manual NZ 24 21.0 Placing the fuel bed: After replacing the firebox (if removed in 17.1) the fuel bed media can now be pl
630184_4 IB Installation Manual NZ 25 IB850 Log & Template Position 4) Line up some of the coals that have been supplied with
630184_4 IB Installation Manual NZ 26 21.2 Locating the Log Set for IB1100: 1) Remove packaging from around log sets 2) Place 2 x rear logs (long
630184_4 IB Installation Manual NZ 27 21.4 Log or Coal Replacement: The fire unit should never be used with broken logs or coals. Turn
630184_4 IB Installation Manual NZ 28 Step 6: Remove and discard the front and middle burners as described in section 24.1 and 24.2 of this man
630184_4 IB Installation Manual NZ 29 Step 7: Attach the Log Template at the left hand side, using the existing screw which is holding the middle
630184_4 IB Installation Manual NZ 3 Contents: Section: Product Description 1.0 Creating the Cavity
630184_4 IB Installation Manual NZ 30 24.0 Gas Type Conversion: Your gas fire has been supplied with the necessary parts for gas conversion. F
630184_4 IB Installation Manual NZ 31 24.5 Step 5: If changing from LPG to NG, slide the supplied burner collar onto the burner tubes of both
630184_4 IB Installation Manual NZ 32 25.0 Checking Operating Pressure: WARNING: The regulator that is supplied with the fire MUST NOT BE REMOVED.
630184_4 IB Installation Manual NZ 33 26.1 Fitting the Fascia Panels: To avoid scratches or knocks to the fascia panels of this heater they must be
630184_4 IB Installation Manual NZ 34 26.2 When installing a 4 sided fascia ensure that the clips that the outer fascia screw into are at the bottom
630184_4 IB Installation Manual NZ 35 28.0 Normal Operating Sounds and Smells; Note: Each time the fire is lit from cold the glass may fog up with
630184_4 IB Installation Manual NZ 36 29.0 Installation Check List: 1 Ensure there is adequate ventilation in the area the appliance
630184_4 IB Installation Manual NZ 37 30.0 WARRANTY TERMS & CONDITIONS: Provided that the Product is installed as per ESCEA’s Installation Man
630184_1 IB Service Manual NZ 11 Wiring Diagram:
630184_1 IB Service Manual NZ 10 Annual service procedure: 1. Isolate power to fire. 2. Remove front glass and clean inside of glass. 3. Remove lo
630184_4 IB Installation Manual NZ 4 1.0 Product Description: The Escea IB1100, IB850 and IB600 gas fires are designed to be built into a cavity. Th
630184_1 IB Service Manual NZ 9 Red auxiliary Button Replacing a Wireless Control: If the wireless control becomes lost or damaged, a new one can be
630184_1 IB Service Manual NZ 8 Note: It is important that the flame rod & spark lead wires sit in this position in the electronic tray. Replacin
630184_1 IB Service Manual NZ 7 Removing or Cleaning Fan As part of regular service procedure, it is recommended that the fan is removed for cleaning
630184_1 IB Service Manual NZ 6 Checking Operating Pressure: This is done at the regulator located at the front RH corner of the appliance. This is b
630184_1 IB Service Manual NZ 5 Cleaning the Log Set and Glass: NEVER RUB THE FASCIA. The outside of the fascias must only be cleaned with a clean d
630184_1 IB Service Manual NZ 4 Or Draught Diverter Sensor Trip The bimetallic snap disk mounted on the hood of the draught diverte
630184_1 IB Service Manual NZ 3 Error Codes: This gas fire has been designed to show error codes to help explain and identify any fault situation tha
630184_1 IB Service Manual NZ 2 Contents: Page: Error Codes 3 Cleaning the Log Set and Glass 5 Checking Ope
630184_1 IB Service Manual NZ IB1100, IB850 and IB600 (Log Fire / Coal Fire) Service Manual NEW ZEALAND EDITION Important
630184_4 IB Installation Manual NZ 5 1.2 Product Dimensions IB850 IB600 Velo (3 sided) Velo (4 sided) A
630184_4 IB Installation Manual NZ 6 IB1100 Velo (3 sided) Velo (4 sided) Quadrato Rado A 1360mm
630184_4 IB Installation Manual NZ 7 CAB2.0 Creating the Cavity: The dimensioned drawing below shows the size of the opening that must be created to
630184_4 IB Installation Manual NZ 8 IB850 & IB1100: Therefore excess = 43MJ/hr - 25.2MJ/hr = 17.8MJ/hr = 4.94kW Wall Vent Opening = 4.94 x 5
630184_4 IB Installation Manual NZ 9 30030150100200Maintain a 30mm clearance around the fascia to ensure ease of fascia removal. NB: No clearance is
Comments to this Manuals